定制个人护理/洗发水瓶盲目的

我需要一个单一的3D或2D渲染的“桩筏”基础基础。我在下面的10个步骤中描述了如何制作它，但如果读者能以某种方式直观地看到它，他们会受益。插图必须是黑白的，灰色阴影是允许的。混凝土、泡沫、土壤等的标准建筑填充模式是可以的。最终的数字预计将在一本小屋建造的书中出版，并由插画师提供应有的荣誉。结构说明如下。如有任何问题，如有不清楚之处，请提出澄清!下面是桩筏基础的施工细节，这种基础可能适用于由于岩石、树根或密实的土而难以用手挖洞到霜冻线的地方。垫基与向下延伸至高承重土壤的驱动销桩相连。与销钉桩的摩擦增加了垫的沉降阻力。 The footing form itself is built of XPS foam, which remains an integral part of the footing insulating against cold penetration from above. Materials per footing: XPS foam insulation (blue or pink) 1 sheet 2’x 8’ x 2” Crack-resistant fiber-reinforced concrete mix (1 80# bag) ½” x 12” concrete anchor bolt 5/8” x 20’ rebar (number depends on driven depth) Construction adhesive (1 tube) Ground-marking paint (1 spray can) Directions: 1) Excavate a square hole 3’x 3’ and ~12” deep. Pile excavated soil on a tarp for later use as backfill. Leave the bottom of this excavation level and soil on bottom undisturbed (important!). 2) Cut four pieces of XPS foam 2’x2’ in size. On 3, find the center, and cut a circular hole with 9” radius (18” diameter) using jig saw or drywall saw. Bond these together with foam-compatible adhesive along the circular cut edge. On the fourth piece of foam, find the center and cut a circular hole with 4” radius (8” diameter). Bond this piece to top of the other three. 3) Lay the XPS form flat on bottom of excavation exactly where the footing/pier will be. Reach inside and spray paint the ground within the form. Then remove the XPS foam form and set aside. 4) Within the painted circle, drive an 8’ length of rebar into the ground as far as it will go, or until just 8” protrudes, whichever comes first. For ease, drive this with a hand-held fence post driver and finish with hand sledge. Cut off protruding rebar 8” above ground (a Milwaukee 12V cordless subcompact bandsaw is an excellent tool for this). 5) Continue in this fashion until you have driven 6 rebar pins, well-spaced, into the footing area, but none closer than 2” to the painted outline of the footing. 6) Using a rebar bender tool, bend the protruding length of each piece of rebar to a ~ 90-degree angle, 3 or 4 inches above the ground. Keep all bends within the footing outline. These bends will lock the rebar into the concrete raft when the footing is poured. 7) Place the previously constructed XPS form on the painted ground surface, enclosing all of the driven pin piles. Mix fiber-reinforced concrete to specifications. Weight form down with cinderblock or large stones and pour mix until it is flush with top of the form. 8) In the center of the 8” diameter hole, insert 12” anchor bolt, pushing through the wet concrete until it hits the ground, leaving 4” exposed. Ensure it’s centered and plumb. Cover exposed concrete with plastic and let the footing cure 72 hours. 9). Cover the form with dirt excavated originally. Grade to drain away from the top of the footing. Seed, and cover with straw until vegetation is established. (Omit this step from drawing....). 10) An 10" diameter round wooden pier will be set on top of this footing. The protruding bolt in the footing will insert in a hole drilled in bottom center of the pier.

这是一个新的儿童玩具，用绳子和积木、滑轮、马达、手推车、马车、钩子和爪子。这些组件可以用临时双面胶带贴在墙壁、天花板和地板上(水平和垂直表面)。以及房间的内外角落、窗户和门框。

我在重新装修我那600平方英尺的后院谷仓式工作室。它已经有了绝缘材料、电、门和窗户，但需要从我们的主屋给水和下水道。我们希望把它变成一个1卧室/1浴室的地方，不知道从哪里开始或如何设计，所以我们正在通过这个比赛寻找一些想法!附加一个非常基本的想法，我把它留给你的创造力来做剩下的。作为参考，我的地址是6150皮尔斯圣阿瓦达，CO. 80003。

我想把我的2D图纸转换成3D效果图，用于我们所有的营销材料。

我们公司正在寻求开发一个独特的室内喷泉。我们正在寻找一个独特的室内喷泉。我们计划在亚马逊上销售，因此，设计是独一无二的，与平台上的其他竞争对手不同。3.除了水流之外，我们还希望喷泉有放蜡烛或熏香的地方，这样就可以成为一种二合一的产品。4.像这样的饮水机应该在室内使用，它们应该在房子里创造一个美妙的环境。一种冥想，平静，放松的感觉，让它在背景中运行。项目尺寸L x W x H:高达9 x 9 x 11英寸产品重量:3磅材料:树脂,供你参考:•100强室内水上喷泉在亚马逊的卖家:www.amazon.com/gp/bestsellers/home-garden/3735981/ref = zg_b_bs_3735981_1•引用一个独特的和独特的设计,结合室内喷泉以及蜡烛/光:www.amazon.com/Alpine-Corporation-Pouring-Tabletop-Fountain/dp/B002YKMPQ6/ref = zg_bs_3735981_2