Viking-styled Liveaboard盲目的

我们公司正在寻求开发一个独特的室内喷泉。我们正在寻找一个独特的室内喷泉。我们计划在亚马逊上销售，因此，设计是独一无二的，与平台上的其他竞争对手不同。3.除了水流之外，我们还希望喷泉有放蜡烛或熏香的地方，这样就可以成为一种二合一的产品。4.像这样的饮水机应该在室内使用，它们应该在房子里创造一个美妙的环境。一种冥想，平静，放松的感觉，让它在背景中运行。项目尺寸L x W x H:高达9 x 9 x 11英寸产品重量:3磅材料:树脂,供你参考:•100强室内水上喷泉在亚马逊的卖家:www.amazon.com/gp/bestsellers/home-garden/3735981/ref = zg_b_bs_3735981_1•引用一个独特的和独特的设计,结合室内喷泉以及蜡烛/光:www.amazon.com/Alpine-Corporation-Pouring-Tabletop-Fountain/dp/B002YKMPQ6/ref = zg_bs_3735981_2

我想把我的2D图纸转换成3D效果图，用于我们所有的营销材料。

在这次比赛中，我们正在评估雇佣20+潜在的设计师来雇佣几个长期的客户项目。请在9月17日上午11点(太平洋夏令时)或更早提交参赛作品。我们正在寻找的技能证明在创建逼真的模型，具体展示你的建模，材料和纹理的真实产品的掌握。请参阅附件，并为6个示例模型中的1个创建设计，这将最好地展示您的渲染才能。使用3ds Max和V-Ray软件进行设计(详见竞赛描述)。每个有效的参赛作品将获得一个奖品。除了标准积分外，符合我们质量标准的参赛作品将获得50个额外积分，以提高他们在Cad Crowd排行榜上的排名。2022世界杯直播时间

寻找一个独特的定制设计瓶为我们的新业务。灵感应该是沐浴和身体工程泡沫洗手皂瓶(下面的链接)。它需要看起来像一个高端时尚品牌的产品。一个签名元素的瓶子应该是我们的标志浮雕在瓶子的一面。这应该是一个突出的功能。我们希望能够将设计扩展到不同尺寸的瓶子150ml, 300ml, 600ml。也寻找瓶子有可互换的分配器顶部盖子，泵和发泡泵的选择。https://www.bathandbodyworks.com/c/hand-soaps/foaming-hand-soap

我需要一个单一的3D或2D渲染的“桩筏”基础基础。我在下面的10个步骤中描述了如何制作它，但如果读者能以某种方式直观地看到它，他们会受益。插图必须是黑白的，灰色阴影是允许的。混凝土、泡沫、土壤等的标准建筑填充模式是可以的。最终的数字预计将在一本小屋建造的书中出版，并由插画师提供应有的荣誉。结构说明如下。如有任何问题，如有不清楚之处，请提出澄清!下面是桩筏基础的施工细节，这种基础可能适用于由于岩石、树根或密实的土而难以用手挖洞到霜冻线的地方。垫基与向下延伸至高承重土壤的驱动销桩相连。与销钉桩的摩擦增加了垫的沉降阻力。 The footing form itself is built of XPS foam, which remains an integral part of the footing insulating against cold penetration from above. Materials per footing: XPS foam insulation (blue or pink) 1 sheet 2’x 8’ x 2” Crack-resistant fiber-reinforced concrete mix (1 80# bag) ½” x 12” concrete anchor bolt 5/8” x 20’ rebar (number depends on driven depth) Construction adhesive (1 tube) Ground-marking paint (1 spray can) Directions: 1) Excavate a square hole 3’x 3’ and ~12” deep. Pile excavated soil on a tarp for later use as backfill. Leave the bottom of this excavation level and soil on bottom undisturbed (important!). 2) Cut four pieces of XPS foam 2’x2’ in size. On 3, find the center, and cut a circular hole with 9” radius (18” diameter) using jig saw or drywall saw. Bond these together with foam-compatible adhesive along the circular cut edge. On the fourth piece of foam, find the center and cut a circular hole with 4” radius (8” diameter). Bond this piece to top of the other three. 3) Lay the XPS form flat on bottom of excavation exactly where the footing/pier will be. Reach inside and spray paint the ground within the form. Then remove the XPS foam form and set aside. 4) Within the painted circle, drive an 8’ length of rebar into the ground as far as it will go, or until just 8” protrudes, whichever comes first. For ease, drive this with a hand-held fence post driver and finish with hand sledge. Cut off protruding rebar 8” above ground (a Milwaukee 12V cordless subcompact bandsaw is an excellent tool for this). 5) Continue in this fashion until you have driven 6 rebar pins, well-spaced, into the footing area, but none closer than 2” to the painted outline of the footing. 6) Using a rebar bender tool, bend the protruding length of each piece of rebar to a ~ 90-degree angle, 3 or 4 inches above the ground. Keep all bends within the footing outline. These bends will lock the rebar into the concrete raft when the footing is poured. 7) Place the previously constructed XPS form on the painted ground surface, enclosing all of the driven pin piles. Mix fiber-reinforced concrete to specifications. Weight form down with cinderblock or large stones and pour mix until it is flush with top of the form. 8) In the center of the 8” diameter hole, insert 12” anchor bolt, pushing through the wet concrete until it hits the ground, leaving 4” exposed. Ensure it’s centered and plumb. Cover exposed concrete with plastic and let the footing cure 72 hours. 9). Cover the form with dirt excavated originally. Grade to drain away from the top of the footing. Seed, and cover with straw until vegetation is established. (Omit this step from drawing....). 10) An 10" diameter round wooden pier will be set on top of this footing. The protruding bolt in the footing will insert in a hole drilled in bottom center of the pier.